OW Lube Oil Heater
HOTSTART OW Weathertight Lube Oil Heater — Use a thermostat with all lube oil heaters to protect the oil from overheating.
Description
HOTSTART OW Weathertight Lube Oil Heater. Use a thermostat with all lube oil heaters to protect the oil from overheating. Lube oil heaters must always be installed in the sump with the entire heater submerged below the oil level at all times. Oil heaters up to 277 V AC meet recognized CSA standards for safety or performance. NOTE: If heating gear oil (medium weight viscosity), HOTSTART recommends using low watt density heaters. See page 21 for remote thermostat part numbers.
- Cord: Weathertight heater-only models are furnished with a 4′ (1.2m) oil- and heat-resistant power cord without plug.
Available models / part numbers — order by part number (all currently out of stock, contact us to order):
| Part No. | Voltage | Watts | Thermostat | Fitting / Probe |
|---|---|---|---|---|
| OW005200-000 | 240 V | 50 W | None | 3/8″ NPT 2-1/8″ (54mm) probe |
| OW212200-000 | 240 V | 125 W | None | 1/2″ NPT 4″ (101mm) probe |
| OW415200-000 | 240 V | 150 W | None | 3/4″ NPT 5″ (127mm) probe |
| OW430800-000 | 208 V | 225 W | None | 3/4″ NPT 5″ (127mm) probe |
| OW430200-000 | 240 V | 300 W | None | 3/4″ NPT 5″ (127mm) probe |
| OW615200-000 | 240 V | 150 W | None | 1″ NPT 5-1/4″ (133mm) probe |
| OW630800-000 | 208 V | 375 W | None | 1″ NPT 5-1/4″ (133mm) probe |
| OW630200-000 | 240 V | 300 W | None | 1″ NPT 5-1/4″ (133mm) probe |
| OW212210-000 | 240 V | 125 W | Fixed 100-120 °F (code 10) | 1/2″ NPT 4″ (101mm) probe |
| OW415210-000 | 240 V | 150 W | Fixed 100-120 °F (code 10) | 3/4″ NPT 5″ (127mm) probe |
| OW430810-000 | 208 V | 225 W | Fixed 100-120 °F (code 10) | 3/4″ NPT 5″ (127mm) probe |
| OW430210-000 | 240 V | 300 W | Fixed 100-120 °F (code 10) | 3/4″ NPT 5″ (127mm) probe |
| OW615210-000 | 240 V | 150 W | Fixed 100-120 °F (code 10) | 1″ NPT 5-1/4″ (133mm) probe |
| OW630810-000 | 208 V | 375 W | Fixed 100-120 °F (code 10) | 1″ NPT 5-1/4″ (133mm) probe |
| OW630210-000 | 240 V | 300 W | Fixed 100-120 °F (code 10) | 1″ NPT 5-1/4″ (133mm) probe |
Technical Information
| Weight | 0.38 kg |
|---|---|
| Dimensions | 24.78 × 5.39 × 5.39 cm |
Brand
Hotstart
Hotstart designs and manufactures engine pre-heating solutions — coolant, oil and immersion heaters, in-block heaters, battery warmers, thermostats and control systems — that keep diesel and gas engines, generators and compressors ready to start in cold conditions. Oz Wide Power supplies the genuine Hotstart range Australia-wide.
You must be logged in to post a review.
Reviews
There are no reviews yet.